The Model 420 is a membrane covered galvanic oxygen probe with built-in two-wire 4-20 mA transmitter. The probe is connected to a DC supply and draws a current of between 4 and 20 mA corresponding to the oxygen concentration.
There are only two wires to connect, and there is no limit to cable length. The output signal is galvanically isolated from the built-in electronics and the process fluid. Interference between the Model 420 and other equipment can never occur!
The OxyGuard Model 420 can therefore be connected directly to a wide range of equipment that can accept a 4-20 mA input, such as alarms, indicators, controllers, recorders, PLC’s, PC systems with A/D input etc.
The Model 420 can also be used to measure gaseous oxygen concentration.
D033 OxyGuard Model 420 DO Probe for 4-20mA
OxyGuard's developed ozone sensor is designed specifically for use in aquaculture. The sensor uses an entirely new innovative technology, and the partial pressure of ozone is measured directly without the use of electrolyte, reagents, light, or other traditional methods. As a result, there is almost no maintenance, the probe is exceptionally stable, and the response time is extremely fast.With the possibility to measure ozone content in the water down to only a few μg/L, it is possible to ensure safe conditions for the stock.
Unit of Measurement: ppm (mg/l)Measuriing Range (Low): 0-0.8mg/l (best between 0 and 0.5)Mesauring Range (High): 0.5-8mg/lOperating Temperature: 0-40CDimensions: 40 x 104mmCable Legnth: 7mResponse Time: 90% in less than 45s (for the low range type)Medium: WaterInstallation: For use with Pacific or Marlin
G20 OxyGuard Ozone Sensor Data Sheet
The OxyGuard Standard Probe – the probe that revolutionised oxygen monitoring.The probe that you can purchase today is even better than the probe introduced in 1987 that helped revolutionize fish farming and make modern aquaculture the industry it is today. Today’s OxyGuard Standard Probe is hermetically sealed. If needed you can open it to replace the membrane and renovate it completely, but this should not be needed for many years.
DescriptionThe measurement stability of the OxyGuard Standard Probe is also very high indeed. A probe measuring in air will maintain accuracy even when subjected to a sudden 20 degree celcius temperature change. The sensitivity of a probe measuring in clean air at room temperature will remain the same for at least 3 years. This proves that the OxyGuard probe is not, like some other probes, affected by “ageing”. OxyGuard believe that the OxyGuard Standard probe is more accurate, needs less attention and maintenance and has a lower total cost of ownership than any other oxygen or dissolved oxygen probe offered to the aquaculture industry today. *Accessories are shipped with every OxyGuard probe. You will thus be able to change the membrane if you manage to damage it during installation. Otherwise the accessories can be enough for up to 5 years’ use.
These OxyGuard probes consist of an electrode and an impedance converter inside a twopart housing held together by a threaded collar. There is extra sealing so that the connections at the top of the electrode remain dry even when the probe is completely submersed. The impedance converter immediately over the electrode eliminates electrical noise problems and permits the use of ordinary cable to connect the probe. Either lightduty or heavy duty OxyGuard pH or redox electrodes with flange fittings can be used.
As standard probes are manufactured from PVC (for temperatures up to 60°C), but on request they can be supplied in other materials, e.g. PP for up to 10 bar at 25 °C, 4 bar at 90 °C, or PVDF for up to 6 bar up to 100°C, 2 bar at 120°C.
There are three basic designs, one for free mounting, one with a 3/4″ tee for flow-through use, the third designed to be screwed into a pipe, flange or other suitable fixture. The probes can be ordered with a 1″ thread at the top of the top part for mounting purposes. OxyGuard also manufacture probes to customer specification, so please ask if you cannot use a standard design. As standard the probes have 7m cables.
For Heavy Duty use in very dirty environments probes can be supplied with a probe cleaning system. This has, for example, proved effective when measuring agricultural slurry – add “C” to ordering number. Several types of mounting device are also available. These are described in separate brochures.
K01 OxyGuard Static pH / Redox Probe
High-quality pH7 calibration solution
Oxyguard pH7 Buffer is the ideal choice for calibrating and testing pH meters and probes. This premium calibration solution ensures accurate results every time, giving you peace of mind during your experiments or testing procedures. With a pH level of 7.00, this buffer solution is formulated to bring your pH meter back to its original factory settings, ensuring precise and reliable measurements.
Easy-to-use formula for hassle-free calibration
With Oxyguard pH7 Buffer, calibrating your pH meter is quick and effortless. Simply immerse your probe into the solution and adjust the readings accordingly to achieve accurate results. This buffer solution is easy to use, making it perfect for both beginners and experienced professionals in the field. Say goodbye to complicated calibration procedures with our convenient pH7 buffer solution!
Reliable and consistent results guaranteed
When it comes to pH calibration and testing, trust Oxyguard pH7 Buffer to deliver reliable and consistent results. Our high-quality formula ensures that your pH meter remains accurate and precise, providing you with the confidence you need in your lab or testing environment. Whether you are conducting research or performing routine measurements, Oxyguard pH7 Buffer is the perfect solution for all your calibration and testing needs.
Hand-held oxygen and temperature meter with NFC tags and Bluetooth technology for easy data transfer to Cobália.
The Polaris C DO meter is a high-performance, low-cost and almost maintenance-free meter for measuring dissolved oxygen and temperature. The meter is sturdy, easy to use and has an extensive longevity making it ideal for harsh conditions.
Polaris C DO can store up to 2500 complete data sets, including time and date stamps. The logged data is stored in the meter or can be transferred to Cobália using Bluetooth.Scan the Cobália NFC tag of the tank and all data will be uploaded to your “digital farm”. Tank specific data assigned to the tags will be stored in Cobália for analyses on temporal variations, multivariable analyses on performance and for the generation of graphs.
The meter has a built-in self-check of all hardware, automatic barometric pressure compensation and a notably short response time. With this meter, you get the high-quality associated with OxyGuard technology and a product that will serve you well for many years.
Instruction Manual
The OxyGuard Polaris C MaxiTemp is a small electronic thermometer specially designed to meet the demands of fish farmers and other professional people for a rugged, reliable and accurate thermometer with data logging function. It has a measuring range of -5 to +45°C with an accuracy of +/- 0.1°, and will measure up to +60°C with an accuracy of +/- 0.2°C. The probe is manufactured in plastic and sea-water resistant stainless steel, and is connected to the display with a 1.5 m cable. Both probe and display are sealed and waterproof.
Values can be stored either automatically at preset time intervals, or manually. You can group values according to the place of measurement. Stored values can be transferred to a PC using the Polaris Link, which connects to the PC via a USB cable.
Pond Master monitors and controls oxygen levels in pond-based aquaculture systems.
Pond Master is specifically designed for monitoring and control of oxygen levels in aquaculture facilities such as shrimp farms, carp farms, and other installations with individual ponds.
This unique instrument incorporates advanced technology with an attractive, compact design resulting in a combination of user-friendly operation, accuracy, low maintenance needs and affordability.
Probe not included
Download Brochure
The OxyGuard Standard Probe – the probe that revolutionised oxygen monitoring.
The probe that you can purchase today is even better than the probe introduced in 1987 that helped revolutionize fish farming and make modern aquaculture the industry it is today.Today’s OxyGuard Standard Probe is hermetically sealed. If needed you can open it to replace the membrane and renovate it completely, but this should not be needed for many years.
The measurement stability of the OxyGuard Standard Probe is also very high indeed. A probe measuring in air will maintain accuracy even when subjected to a sudden 20 degree celcius temperature change. The sensitivity of a probe measuring in clean air at room temperature will remain the same for at least 3 years. This proves that the OxyGuard probe is not, like some other probes, affected by “ageing”.
OxyGuard believe that the OxyGuard Standard probe is more accurate, needs less attention and maintenance and has a lower total cost of ownership than any other oxygen or dissolved oxygen probe offered to the aquaculture industry today.
*Accessories are shipped with every OxyGuard probe. You will thus be able to change the membrane if you manage to damage it during installation. Otherwise the accessories can be enough for up to 5 years’ use.
The OxyGuard Salinity Probe is specially designed for aquaculture use. Factory calibration and automatic temperature compensation make it very easy to use. It is found in two versions. One is a 3-wire 4-20 mA sensor – connect it to 24 VDC and the output varies between 4 and 20 mA according to the salinity. The other has data bus connection for use with OxyGuard Pacific.
The probe is designed to be as trouble-free as possible, with features specially suited for aquacultural use. Inductive technology is used so that you don’t have to worry about deposits on the surface of the probe – all you have to do is ensure that the hole in the probe is open and relatively clean.
The probe measures salinity according to the internationally agreed PSS-78 scale (Practical Salinity Scale 78).
The OxyGuard Salinity Probe is specially designed for aquaculture use. Factory calibration and automatic temperature compensation make it very easy to use. It is found in two versions. One is a 3-wire 4-20 mA sensor – connect it to 24 VDC and the output varies between 4 and 20 mA according to the salinity. The other has data bus connection for use with OxyGuard Pacific.
The probe is designed to be as trouble-free as possible, with features specially suited for aquacultural use. Inductive technology is used so that you don’t have to worry about deposits on the surface of the probe – all you have to do is ensure that the hole in the probe is open and relatively clean.
The probe measures salinity according to the internationally agreed PSS-78 scale (Practical Salinity Scale 78).
The OxyGuard Standard Probe – the probe that revolutionised oxygen monitoring.
The probe that you can purchase today is even better than the probe introduced in 1987 that helped revolutionize fish farming and make modern aquaculture the industry it is today.Today’s OxyGuard Standard Probe is hermetically sealed. If needed you can open it to replace the membrane and renovate it completely, but this should not be needed for many years.
The measurement stability of the OxyGuard Standard Probe is also very high indeed. A probe measuring in air will maintain accuracy even when subjected to a sudden 20 degree celcius temperature change. The sensitivity of a probe measuring in clean air at room temperature will remain the same for at least 3 years. This proves that the OxyGuard probe is not, like some other probes, affected by “ageing”.
OxyGuard believe that the OxyGuard Standard probe is more accurate, needs less attention and maintenance and has a lower total cost of ownership than any other oxygen or dissolved oxygen probe offered to the aquaculture industry today.
*Accessories are shipped with every OxyGuard probe. You will thus be able to change the membrane if you manage to damage it during installation. Otherwise the accessories can be enough for up to 5 years’ use.
OxyGuard temperature probes are robust, accurate and easy to use. They are filled with a special compound that protects against moisture. As standard the probes are fitted with 7 m cable, but they can be supplied with other lengths on request. The sensor in both types of probe consists of a stainless steel cylinder containing the thermistor or Pt100 element. This sensor tip is fitted to a black plastic housing. Standard types of housing are shown overleaf, but others can be supplied on request, e.g. to fit other pipe threads or fittings.
The OxyGuard TGP probe measures Total dissolved Gas Pressure and is designedspecifically for use with OxyGuard Commander or Pacific systems. It can be addedto existing systems. It contains sensors for dissolved gas pressure and temperature.The gases dissolved in water consist of oxygen and “other gases”. “Other gases” aremainly nitrogen. It is important to measure if the water is supersaturated in order toprevent the fish from getting gas bubble disease.
The Commander or Pacific system to which the probe is connected uses a dissolvedoxygen measurement made by a DO probe placed near the TGP probe forcalculations and presents the degrees of saturation for the total gas, dissolvedoxygen and for “other gas”.
F01 OxyGuard Total Gas Pressure probe
The OxyGuard Standard Probe – the probe that revolutionised oxygen monitoring.
The probe that you can purchase today is even better than the probe introduced in 1987 that helped revolutionize fish farming and make modern aquaculture the industry it is today.Today’s OxyGuard Standard Probe is hermetically sealed. If needed you can open it to replace the membrane and renovate it completely, but this should not be needed for many years.
The measurement stability of the OxyGuard Standard Probe is also very high indeed. A probe measuring in air will maintain accuracy even when subjected to a sudden 20 degree celcius temperature change. The sensitivity of a probe measuring in clean air at room temperature will remain the same for at least 3 years. This proves that the OxyGuard probe is not, like some other probes, affected by “ageing”.
OxyGuard believe that the OxyGuard Standard probe is more accurate, needs less attention and maintenance and has a lower total cost of ownership than any other oxygen or dissolved oxygen probe offered to the aquaculture industry today.
*Accessories are shipped with every OxyGuard probe. You will thus be able to change the membrane if you manage to damage it during installation. Otherwise the accessories can be enough for up to 5 years’ use.
Pentair plastic - filter housings are the accepted world standard for high quality, performance and economy. Offering the most comprehensive range of vessels, they are constructed for long life, durability, ease of use and are available in a variety of materials for specialist applications. Meeting internationally recognised technical standards, Pentair test continually throughout production, enabling them to guarantee their products for the recommended application. To ensure quality is not compromised, only virgin materials are used during manufacturing with polypropylene and styrene-acrylonitrile (SAN) vessels being FDA compliant.
Upgrade your water filtration system with the PBR-410-BKBASKET, a Pentair 10" Basket designed specifically for use with PBH-410 Bag Housing (155374-03). This high-quality component ensures efficient filtration and a reliable performance, making it essential for maintaining optimal water quality.
Key Features and Benefits:
Durable Construction: Made with robust materials to ensure long-lasting use, even under demanding filtration conditions.
Perfect Compatibility: Specifically engineered for PBH-410 Bag Housing systems to ensure seamless integration and maximum efficiency.
Efficient Filtration Support: Provides reliable support for bag filters, optimizing their performance in capturing impurities and delivering cleaner water.
Hassle-Free Replacement: Designed for easy installation, making the process of upgrading or replacing your existing basket quick and straightforward.
Trusted Quality: Supplied by GAPS Water Treatment, a reputable provider of premium water treatment components to enhance your system's reliability.
Whether you're operating a residential or commercial water filtration system, the PBR-410-BKBASKET ensures unparalleled performance and durability. Its innovative design and compatibility with the PBH-410 Bag Housing make it a smart choice for anyone looking to enhance their water treatment setup.
Standard Filter Housings are manufactured of a durable polypropylene or clear Styrene-Acrylonitrile (SAN). All are equipped with 3/4" NPT inlet and outlet ports. Standard Filter Housings are available in both 10" and 20" lengths and will accommodate a wide range of 2-1/2" to 2-7/8" diameter cartridges. The reinforced polypropylene cap offers an optional pressure relief button on the inlet side to relieve pressure inside the housing when changing filter cartridges.Reinforced polypropylene housings have excellent chemical resistance and are ideal for many residential, commercial and industrial applications. Clear sumps offer on-site examination of the cartridge.Opaque Standard Filter Housings are moulded from rugged reinforced polypropylene. They offer outstanding chemical compatibility and are ideal for use in a variety of low-flow applications.Clear Standard Filter Housings offer on-site examination of flow, performance, and cartridge life. They are ideal for a variety of applications.Features, Options, & Benefits
Ideal for a wide range of applications, including residential, commercial and industrial
Available in 10" and 20" lengths
Optional pressure relief/bleed button on inlet side of cap
Thick walls for increased strength
Leak-proof sealing with top-seated Buna-N O-ring
Available with clear or opaque sumps
Specifications
Housing - Polypropylene (opaque) or Styrene Acrylonitrile (clear)
Cap - Reinforced polypropylene
Button Assembly - 300-Series stainlesssteel, EPDM, and polypropylene
Temperature Rating - 4.4-51.7°C
Maximum Pressure - 125 psi (8.6 bar)
NSF CertificationsThe 150001, 150002, 150067, 150068, 150071, 150072, 150435 and 150436 are Tested and Certified by NSF International to NSF/ANSI Standard 42 for material and structural integrity requirements.
Standard Filter Housings are manufactured of a durable polypropylene or clear Styrene-Acrylonitrile (SAN). All are equipped with 3/4" NPT inlet and outlet ports. Standard Filter Housings are available in both 10" and 20" lengths and will accommodate a wide range of 2-1/2" to 2-7/8" diameter cartridges. The reinforced polypropylene cap offers an optional pressure relief button on the inlet side to relieve pressure inside the housing when changing filter cartridges.Reinforced polypropylene housings have excellent chemical resistance and are ideal for many residential, commercial and industrial applications. Clear sumps offer on-site examination of the cartridge.Opaque Standard Filter Housings are moulded from rugged reinforced polypropylene. They offer outstanding chemical compatibility and are ideal for use in a variety of low-flow applications.Clear Standard Filter Housings offer on-site examination of flow, performance, and cartridge life. They are ideal for a variety of applications.Features, Options, & Benefits
Ideal for a wide range of applications, including residential, commercial and industrial
Available in 10" and 20" lengths
Optional pressure relief/bleed button on inlet side of cap
Thick walls for increased strength
Leak-proof sealing with top-seated Buna-N O-ring
Available with clear or opaque sumps
Specifications
Housing - Polypropylene (opaque) or Styrene Acrylonitrile (clear)
Cap - Reinforced polypropylene
Button Assembly - 300-Series stainlesssteel, EPDM, and polypropylene
Temperature Rating - 4.4-51.7°C
Maximum Pressure - 125 psi (8.6 bar)
NSF CertificationsThe 150001, 150002, 150067, 150068, 150071, 150072, 150435 and 150436 are Tested and Certified by NSF International to NSF/ANSI Standard 42 for material and structural integrity requirements.
Standard Filter Housings are manufactured of a durable polypropylene or clear Styrene-Acrylonitrile (SAN). All are equipped with 3/4" NPT inlet and outlet ports. Standard Filter Housings are available in both 10" and 20" lengths and will accommodate a wide range of 2-1/2" to 2-7/8" diameter cartridges. The reinforced polypropylene cap offers an optional pressure relief button on the inlet side to relieve pressure inside the housing when changing filter cartridges.Reinforced polypropylene housings have excellent chemical resistance and are ideal for many residential, commercial and industrial applications. Clear sumps offer on-site examination of the cartridge.Opaque Standard Filter Housings are moulded from rugged reinforced polypropylene. They offer outstanding chemical compatibility and are ideal for use in a variety of low-flow applications.Clear Standard Filter Housings offer on-site examination of flow, performance, and cartridge life. They are ideal for a variety of applications.Features, Options, & Benefits
Ideal for a wide range of applications, including residential, commercial and industrial
Available in 10" and 20" lengths
Optional pressure relief/bleed button on inlet side of cap
Thick walls for increased strength
Leak-proof sealing with top-seated Buna-N O-ring
Available with clear or opaque sumps
Specifications
Housing - Polypropylene (opaque) or Styrene Acrylonitrile (clear)
Cap - Reinforced polypropylene
Button Assembly - 300-Series stainlesssteel, EPDM, and polypropylene
Temperature Rating - 4.4-51.7°C
Maximum Pressure - 125 psi (8.6 bar)
NSF CertificationsThe 150001, 150002, 150067, 150068, 150071, 150072, 150435 and 150436 are Tested and Certified by NSF International to NSF/ANSI Standard 42 for material and structural integrity requirements.Part numbers: 150071, 150072, 150435, 150436, 150106, 150096
Pressure gauges are an essential addition to any housing system by eliminating any guesswork for filter changeouts, maximising filter cartridge life and optimising system performance. Available in various thread sizes and orientations plus further technical options with differing maximum pressure ratings and features to suit more challenging applications.
Pentair 3G Standard Series Housings feature integral brackets, 20" clear housings, and caps for differential pressure gauges. They accept standard double open end (DOE) and our O-ring sealing cartridges. The O-ring design offers enhanced cartridge sealing for critical cartridge applications.3G Standard Filter Housings are manufactured from durable polypropylene or clear Styrene-Acrylonitrile (SAN). Reinforced polypropylene housings have excellent chemical resistance and are ideal for many residential, commercial and industrial applications. Clear sumps are manufactured from Styrene-Acrylonitrile (SAN). They offer on-site examination of the cartridge and have excellent chemical compatibility.All are equipped with 3/4" inlet and outlet ports. 3G Standard Filter Housings are available in 10" and 20" lengths and will accommodate a wide range of 2-1/4" to 3-1/8" diameter cartridges.Features, Options, & Benefits
Integral bracket and mounting boss cap version available
Available in 10" and 20" sumps in clear and opaque
Buttress threads and uniform walls for easier cartridge change and improved strength
Accepts CG o-ring sealing cartridges as well as standard DOE cartridges
Optional pressure-relief/bleed button and differential pressure gauge
Leak-proof sealing with top-seated floating Buna-N O-ring
Specifications
Housing - Polypropylene (opaque) or Styrene Acrylonitrile (clear)
Cap - Reinforced polypropylene
Button Assembly - 300-Series stainless-steel, EPDM, and polypropylene
Temperature Rating - 4.4-51.7°C
Maximum Pressure - 125 psi (8.6 bar)
Pentair 3G Standard Series Housings feature integral brackets, 20" clear housings, and caps for differential pressure gauges. They accept standard double open end (DOE) and our O-ring sealing cartridges. The O-ring design offers enhanced cartridge sealing for critical cartridge applications.3G Standard Filter Housings are manufactured from durable polypropylene or clear Styrene-Acrylonitrile (SAN). Reinforced polypropylene housings have excellent chemical resistance and are ideal for many residential, commercial and industrial applications. Clear sumps are manufactured from Styrene-Acrylonitrile (SAN). They offer on-site examination of the cartridge and have excellent chemical compatibility.All are equipped with 3/4" inlet and outlet ports. 3G Standard Filter Housings are available in 10" and 20" lengths and will accommodate a wide range of 2-1/4" to 3-1/8" diameter cartridges.Features, Options, & Benefits
Integral bracket and mounting boss cap version available
Available in 10" and 20" sumps in clear and opaque
Buttress threads and uniform walls for easier cartridge change and improved strength
Accepts CG o-ring sealing cartridges as well as standard DOE cartridges
Optional pressure-relief/bleed button and differential pressure gauge
Leak-proof sealing with top-seated floating Buna-N O-ring
Specifications
Housing - Polypropylene (opaque) or Styrene Acrylonitrile (clear)
Cap - Reinforced polypropylene
Button Assembly - 300-Series stainless-steel, EPDM, and polypropylene
Temperature Rating - 4.4-51.7°C
Maximum Pressure - 125 psi (8.6 bar)
Pentair 3G Standard Series Housings feature integral brackets, 20" clear housings, and caps for differential pressure gauges. They accept standard double open end (DOE) and our O-ring sealing cartridges. The O-ring design offers enhanced cartridge sealing for critical cartridge applications.3G Standard Filter Housings are manufactured from durable polypropylene or clear Styrene-Acrylonitrile (SAN). Reinforced polypropylene housings have excellent chemical resistance and are ideal for many residential, commercial and industrial applications. Clear sumps are manufactured from Styrene-Acrylonitrile (SAN). They offer on-site examination of the cartridge and have excellent chemical compatibility.All are equipped with 3/4" inlet and outlet ports. 3G Standard Filter Housings are available in 10" and 20" lengths and will accommodate a wide range of 2-1/4" to 3-1/8" diameter cartridges.Features, Options, & Benefits
Integral bracket and mounting boss cap version available
Available in 10" and 20" sumps in clear and opaque
Buttress threads and uniform walls for easier cartridge change and improved strength
Accepts CG o-ring sealing cartridges as well as standard DOE cartridges
Optional pressure-relief/bleed button and differential pressure gauge
Leak-proof sealing with top-seated floating Buna-N O-ring
Specifications
Housing - Polypropylene (opaque) or Styrene Acrylonitrile (clear)
Cap - Reinforced polypropylene
Button Assembly - 300-Series stainless-steel, EPDM, and polypropylene
Temperature Rating - 4.4-51.7°C
Maximum Pressure - 125 psi (8.6 bar)
The PBR-420-BKBASKET, a premium-grade PENTAIR 20" Basket, is specifically engineered for compatibility with the PBH-420 Bag Housing (155373-03). Supplied by GAPS Water Treatment, this durable and reliable component ensures maximum performance in your filtration applications.
Key Features:
Designed for PBH-420 Bag Housing, guaranteeing an exact fit and seamless operation
Generous 20" size, accommodating high-capacity filtration requirements
Constructed with durable materials, ensuring long-lasting use and resistance to wear
Easy installation, minimizing downtime and enabling hassle-free system setup
Ideal for various filtration applications, providing versatility and efficiency
Benefits:
Optimizes filtration efficiency, enhancing overall system performance and water quality
Reliable and robust design ensures consistent operation even under challenging conditions
Simplifies system upkeep with its straightforward installation and maintenance
Suitable for diverse residential, commercial, and industrial filtration needs, offering flexibility
Extends the lifespan of your filtration system with its durable construction
The PBR-420-BKBASKET is an essential component for those utilizing PBH-420 Bag Housing, offering a combination of durability, efficiency, and reliability. Whether it's for residential or industrial purposes, this high-quality basket ensures your filtration system operates at its best. Trust in its robust design and seamless compatibility to keep your water treatment processes running smoothly.
Standard Filter Housings are manufactured of a durable polypropylene or clear Styrene-Acrylonitrile (SAN). All are equipped with 3/4" NPT inlet and outlet ports. Standard Filter Housings are available in both 10" and 20" lengths and will accommodate a wide range of 2-1/2" to 2-7/8" diameter cartridges. The reinforced polypropylene cap offers an optional pressure relief button on the inlet side to relieve pressure inside the housing when changing filter cartridges.Reinforced polypropylene housings have excellent chemical resistance and are ideal for many residential, commercial and industrial applications. Clear sumps offer on-site examination of the cartridge.Opaque Standard Filter Housings are moulded from rugged reinforced polypropylene. They offer outstanding chemical compatibility and are ideal for use in a variety of low-flow applications.Clear Standard Filter Housings offer on-site examination of flow, performance, and cartridge life. They are ideal for a variety of applications.Features, Options, & Benefits
Ideal for a wide range of applications, including residential, commercial and industrial
Available in 10" and 20" lengths
Optional pressure relief/bleed button on inlet side of cap
Thick walls for increased strength
Leak-proof sealing with top-seated Buna-N o-ring
Available with clear or opaque sumps
Specifications
Housing - Polypropylene (opaque) or Styrene Acrylonitrile (clear)
Cap - Reinforced polypropylene
Button Assembly - 300-Series stainless-steel, EPDM, and polypropylene
Temperature Rating - 4.4-51.7°C
Maximum Pressure - 125 psi (8.6 bar)
NSF CertificationsThe 150001, 150002, 150067, 150068, 150071, 150072, 150435 and 150436 are Tested and Certified by NSF International to NSF/ANSI Standard 42 for material and structural integrity requirements.
Standard Filter Housings are manufactured of a durable polypropylene or clear Styrene-Acrylonitrile (SAN). All are equipped with 3/4" NPT inlet and outlet ports. Standard Filter Housings are available in both 10" and 20" lengths and will accommodate a wide range of 2-1/2" to 2-7/8" diameter cartridges. The reinforced polypropylene cap offers an optional pressure relief button on the inlet side to relieve pressure inside the housing when changing filter cartridges.Reinforced polypropylene housings have excellent chemical resistance and are ideal for many residential, commercial and industrial applications. Clear sumps offer on-site examination of the cartridge.Opaque Standard Filter Housings are moulded from rugged reinforced polypropylene. They offer outstanding chemical compatibility and are ideal for use in a variety of low-flow applications.Clear Standard Filter Housings offer on-site examination of flow, performance, and cartridge life. They are ideal for a variety of applications.Features, Options, & Benefits
Ideal for a wide range of applications, including residential, commercial and industrial
Available in 10" and 20" lengths
Optional pressure relief/bleed button on inlet side of cap
Thick walls for increased strength
Leak-proof sealing with top-seated Buna-N o-ring
Available with clear or opaque sumps
Specifications
Housing - Polypropylene (opaque) or Styrene Acrylonitrile (clear)
Cap - Reinforced polypropylene
Button Assembly - 300-Series stainless-steel, EPDM, and polypropylene
Temperature Rating - 4.4-51.7°C
Maximum Pressure - 125 psi (8.6 bar)
NSF CertificationsThe 150001, 150002, 150067, 150068, 150071, 150072, 150435 and 150436 are Tested and Certified by NSF International to NSF/ANSI Standard 42 for material and structural integrity requirements.
Pentair Big Clear Filter Housings offer the versatility to meet all of your large capacity filtration needs, including high-flow and heavy-sediment applications. The extra large housing allows for greater cartridge capacity, reducing the number of vessels required for high flow-rate applications. Sumps are available in both 10" and 20" lengths.Big Clear Filter Housings offer on-site examination of flow, performance, and cartridge life and are ideal for a variety of applications. The 1" polypropylene caps are available with a pressure-relief button on the inlet side to relieve pressure inside the housing and are available in 10" and 20" lengths.Caps are constructed of reinforced polypropylene. The 10" sumps are made of Lexan® and the 20" sumps are SAN (Styrene acrylonitrile)Features, Options, & Benefits
Large capacity housing suitable for high flow applications
Available in 10" and 20" lengths
Pressure relief/bleed on inlet side of cap
Accepts 4-1/2" diameter cartridges
Specifications
Housing - Styrene Acrylonitrile (clear)
Cap - Reinforced polypropylene
Button Assembly - 300-Series stainless-steel, EPDM, and polypropylene
Maximum Temperature - 38°C
•Maximum Pressure - 10": 6.9 bar, 20" 6.2 bar
The PBH-410-1NPT from Pentair is a durable 10" polypropylene bag housing designed for efficient water filtration. Featuring 1" NPT ports, this housing is perfect for various low-flow applications, including residential prefiltration, food service, and industrial water treatment. Constructed from lightweight, corrosion-resistant polypropylene, it ensures longevity and chemical compatibility. It accommodates one BP/BN 410 bag (8" x 4.5") and operates efficiently at a maximum pressure of 6.9 bar and a flow rate of 50 lpm. The EPDM seal and temperature rating of 38°C make it suitable for a wide range of environments.
Key Features
Material: Polypropylene
Configuration: 1 x BP/BN 410 Bag (L: 8" x D: 4.5")
Port Size: 1" NPT
Seal: EPDM
Temperature Rating: 38°C
Max Pressure: 6.9 bar
Flow Rate: 50 lpm
Color: Blue with Black Cap
Includes: Gauge, wrench, and 3/8" drain valve
Chemical Compatibility: Outstanding, suitable for various applications
Applications
Residential Prefiltration: Ideal for removing sediments and particulates before water enters the home.
Food Service: Ensures clean and safe water for food preparation and service.
Industrial Water Treatment: Suitable for various industrial processes requiring clean water.
Chemical Filtration: Compatible with a wide range of chemicals, making it versatile for different industries.
The PBH-410-1.5BT from Pentair is a robust 10" polypropylene bag housing designed for efficient water filtration. Featuring 1.5" BSP ports, this housing is ideal for various low-flow applications, including residential prefiltration, food service, and industrial water treatment. The unit is constructed from lightweight, corrosion-resistant polypropylene, ensuring durability and chemical compatibility. It accommodates one BP/BN 410 bag (8" x 4.5") and operates efficiently at a maximum pressure of 6.9 bar and a flow rate of 50 lpm. The EPDM seal and temperature rating of 38°C make it suitable for a wide range of environments.
Key Features
Material: Polypropylene
Configuration: 1 x BP/BN 410 Bag (L: 8" x D: 4.5")
Port Size: 1.5" BSP
Seal: EPDM
Temperature Rating: 38°C
Max Pressure: 6.9 bar
Flow Rate: 50 lpm
Color: Blue with Black Cap
Includes: Gauge, wrench, and 3/8" drain valve
Chemical Compatibility: Outstanding, suitable for various applications
Applications
Residential Prefiltration: Ideal for removing sediments and particulates before water enters the home.
Food Service: Ensures clean and safe water for food preparation and service.
Industrial Water Treatment: Suitable for various industrial processes requiring clean water.
Chemical Filtration: Compatible with a wide range of chemicals, making it versatile for different industries.
The PBH-420-1NPT from Pentair is a durable 20" polypropylene bag housing designed for efficient water filtration. Featuring 1" NPT ports, this housing is perfect for various low-flow applications, including residential prefiltration, food service, and industrial water treatment. Constructed from lightweight, corrosion-resistant polypropylene, it ensures longevity and chemical compatibility. It accommodates one BP/BN 420 bag (18" x 4.5") and operates efficiently at a maximum pressure of 6.9 bar and a flow rate of 100 lpm. The EPDM seal and temperature rating of 38°C make it suitable for a wide range of environments.
Key Features
Material: Polypropylene
Configuration: 1 x BP/BN 420 Bag (L: 18" x D: 4.5")
Port Size: 1" NPT
Seal: EPDM
Temperature Rating: 38°C
Max Pressure: 6.9 bar
Flow Rate: 100 lpm
Color: Blue with Black Cap
Includes: Gauge, wrench, and 3/8" drain valve
Chemical Compatibility: Outstanding, suitable for various applications
Applications
Residential Prefiltration: Ideal for removing sediments and particulates before water enters the home.
Food Service: Ensures clean and safe water for food preparation and service.
Industrial Water Treatment: Suitable for various industrial processes requiring clean water.
Chemical Filtration: Compatible with a wide range of chemicals, making it versatile for different industries.
The PBH-420-1.5BT from Pentair is a durable 20" polypropylene bag housing designed for efficient water filtration. Featuring 1.5" BSP ports, this housing is perfect for various low-flow applications, including residential prefiltration, food service, and industrial water treatment. Constructed from lightweight, corrosion-resistant polypropylene, it ensures longevity and chemical compatibility. It accommodates one BP/BN 420 bag (18" x 4.5") and operates efficiently at a maximum pressure of 6.9 bar and a flow rate of 100 lpm. The EPDM seal and temperature rating of 38°C make it suitable for a wide range of environments.
Key Features
Material: Polypropylene
Configuration: 1 x BP/BN 420 Bag (L: 18" x D: 4.5")
Port Size: 1.5" BSP
Seal: EPDM
Temperature Rating: 38°C
Max Pressure: 6.9 bar
Flow Rate: 100 lpm
Color: Blue with Black Cap
Includes: Gauge, wrench, and 3/8" drain valve
Chemical Compatibility: Outstanding, suitable for various applications
Applications
Residential Prefiltration: Ideal for removing sediments and particulates before water enters the home.
Food Service: Ensures clean and safe water for food preparation and service.
Industrial Water Treatment: Suitable for various industrial processes requiring clean water.
Chemical Filtration: Compatible with a wide range of chemicals, making it versatile for different industries.
High-Quality Bracket Kit
This Pentair BB & PBH Housing 316 Stainless Steel plated bracket kit is a durable and reliable accessory designed to enhance the performance of your water filtration system. Made from high-quality stainless steel, this bracket kit is built to last and withstand the rigors of daily use. The sleek design adds a touch of elegance to your filtration system while ensuring secure installation.
Easy Installation Process
With this kit, you'll receive all the necessary screws for a hassle-free installation process. The included screws are specifically designed for use with the Pentair BB & PBH housing, ensuring a perfect fit and easy assembly. Whether you're a DIY enthusiast or a professional installer, you'll appreciate the convenience and simplicity of installing this bracket kit.
Secure Your Filtration System
Ensure the stability and security of your Pentair BB & PBH housing with this stainless steel plated bracket kit. By securely mounting your filtration system with this kit, you can have peace of mind knowing that it will remain in place and function effectively. Take your water filtration to the next level with this reliable and sturdy bracket kit.
